Manufacturing Requirements For Snow Boots

Sep 03, 2026

Leave a message

Traditional craftsmanship represents one of the oldest methods for producing snow boots, with the process carried out primarily by hand, step by step. It begins with the selection of materials; high-quality natural leather and fur are considered the best raw materials for snow boots. Next, patterns are created-outlining the shape of the boot on cardboard-which then serve as templates for crafting the soles, linings, and insulating layers. This is followed by cutting the selected materials according to these templates, after which the components are stitched together, the soles are attached, and the fur is secured in place.

1. Lasting (Inserting the Last): The shoe last is inserted into the upper. It must be positioned so that the forefoot area is flat and the front and back are perfectly aligned-without any shifting, twisting, or distortion-to ensure the upper conforms precisely to the shape of the last. During this process, particular attention must be paid to the center line of the forefoot. Shoe lasts come in various structural types, such as single-piece, two-piece, hinged (opening-top), and spring-loaded lasts. Once the last is properly inserted, the boot is placed into a heating machine to set its shape.

2. Applying Adhesive: Glue is applied to the bottom edge of the upper and to the sole. The adhesive must be applied evenly along the perimeter, ensuring a smooth, continuous line without any gaps or irregularities.

Adhesives (shoe-making glues) are categorized into solvent-based and solvent-free types. Traditional oil-based (solvent-based) glues utilize organic solvents, whereas water-based polyurethane (PU) glues are more environmentally friendly; however, the latter may offer lower bonding strength and reduced breathability. Snow boots primarily utilize PU-based adhesives and GCR-grafted chloroprene (neoprene) adhesives.

Before applying adhesive to the sole, a "primer" (treatment agent) must be used. This agent acts as a bridge, conditioning the surface of the sole to facilitate better adhesion. It is crucial to select the correct primer based on the specific material-whether it is PU, PVC, rubber, EVA, TPR, nylon, or oiled leather. Using the wrong primer will render the process ineffective. Regardless of the type, the primer must be allowed to dry completely; otherwise, it may have the opposite effect. Drying the primer with heat is even more effective. Foamed soles must be abraded (sanded) before adhesive application. If the outsole material is too soft, a hardening agent (curing agent) should be added to the adhesive to increase the sole's rigidity-typically at a concentration of 3% to 5%.

Adhesive application techniques include scraping, rolling, dragging, smearing, and brushing. Operators generally develop a preferred side of the brush, a specific application method, and a consistent direction of movement. The choice of brush specifications varies depending on the individual and the specific task-brushes may be large or small, with long or short bristles. Black hog bristles are preferred for their resilience. Some prefer to trim the bristles into a flat edge, others into a rounded or angled shape; there is no "best" shape-the right choice is simply whatever feels most comfortable and allows for efficient, high-quality work. When applying adhesive to the lasting margin (the edge of the shoe upper), use a pulling motion: apply force with your index finger while keeping your wrist suspended, ensuring even pressure and a smooth, continuous stroke.

3. Sole attachment-also known as "sole bonding"-involves joining the outsole to the shoe upper. This process requires precise alignment of the front and rear center points, uniform margins, and bilateral symmetry. The outsole must not be twisted, and there should be no visible glue residue or gaps.

Temperature control is critical. Settings must be adjusted based on the length of the production line and the conveyor speed, as well as the specific materials of the upper and the outsole. For PU adhesive (often called "white glue" by shoemakers), the temperature range is 5°C–150°C. Grafted chloroprene adhesive (known as "yellow glue") requires a lower temperature setting; if the temperature is too high, the adhesive will "die" (lose its bonding properties). When attaching the sole, the adhesive must be sufficiently dry, and the temperature must be moderate. If the adhesive is not dry, the bond will be weak, and "stringing" (glue stretching into filaments) may occur during pressing. For TPR outsoles using PU adhesive, a temperature that is too low results in a weak bond (the sole may peel off easily), while a temperature that is too high can cause the outsole to deform or the edges to bulge out during pressing. When using a small drying oven, allow the applied adhesive to air-dry for 8–16 minutes to ensure the solvents have evaporated before bonding.

In industry terminology, "offset" (or *kun* in Chinese) refers to a deviation of the center point. If the center point shifts toward the inner ankle, it is called "inner offset"; if it shifts toward the outer ankle, it is "outer offset." Because the center line of the last bottom is shorter and wider on the inner side and narrower and longer on the outer side, it is better to have an "inner offset" than an "outer offset." The center point must be aligned accurately; otherwise, subsequent operations will be difficult. During sole attachment, the entire contact area must be bonded to the adhesive. If the outsole is slightly larger than the upper, "pinch" the outsole toward the upper; if the outsole is slightly smaller, "pinch" the upper toward the outsole. Finally, press out any trapped air at the waist (the arch/waist area of ​​the shoe) to prevent air pressure from rupturing the bond during wear. 4. Pressing: Place the shoe-with the outsole attached-into a pressing machine. The pressing duration should be 5–8 seconds, with a pressure of 20–40 kN. Use higher pressure for EVA outsoles; for TPR outsoles, keep the pressure moderate to avoid edge displacement (slippage). After pressing, the shoe is moved to a cooling machine to set its shape.

5. Last removal: Extract the shoe last from the footwear; this completes the sole-attachment process. For men's footwear, the bond strength-measured via a 90-degree peel test-must be at least 5.4 kN/m.